The QNAP TL-D800C Hardware Review

New NAS Expansion for a New Decade – But Is the QNAP TL-D800C Worth Your Data?

If you have been the owner of a NAS server for a few years, you know that available space will always be an eventual barrier in the end. Even in the very early days of network-attached storage it was already being pre-emptively considered. A NAS drive is not like most other computer hardware, in that an upgrade can be conducted on a hardware level, without significant impact on the software level. Sure, you can upgrade your NAS to a new model a few years down the line, but when you do that, it will almost certainly require all your shared files, paths and connected users to be shifted or changed. That is why when the inevitable day when your available space hits zero, you will be wondering how to proceed. Many home and small business users will use this as an opportunity to upgrade their NAS to a new model, move the HDDs over (in their RAID), all the while crossing their fingers and praising their backups, with ‘almost’ 100% confidence that the data migration will be fine and drives will continue to function as they did on day 1. But that still needs you to spend big on new hardware almost certainly more than your first NAS, as well as the loss of time (very dependant on your own setup) to repairing, replacing and recreating those existing network connections. It is for reasons like this that many users will consider the often more cost-effective AND easier to adapt NAS expansion option. The ability to add an additional HDD enclosure that will ‘bolt-on’ additional hard drive bays to their existing NAS RAID storage system and allow you to expand your available space has been around for almost as long as NAS itself, sometimes being used as local sync’d backups, as completely separate storage pools or just expanding the primary RAID accordingly. Today I want to discuss one of the several new QNAP NAS expansions revealed in their new TR and TL expansion series(full guide here), the brand new TL-D800C. This is their new 8 SATA Bay expansion device that arrives with USB 3.1 Gen 2 USB-C Support (10Gb/s) and is designed to be an affordable and reliable way to expand your storage, arriving at just over £400 – it is a whole lot lower in price than a new 8-Bay NAS, with the added benefit that it is also PC and Mac supported, so it can be used as a traditional DAS too. Some might argue that as it is JBOD, it has limited use outside of a NAS expansion (whereby the NAS CPU can conduct the RAID configuration and support) but we fast see a resurgence in JBOD use, with many users looking at thunderbolt and SAS solutions that have fast access and just do what they are told! There is no avoiding that the TL-D800C is not for everyone, with some looking at the TR series (hardware RAID built-in) instead. So, let’s take a look and serif the QNAP TL-D800C deserves your data.

QNAP TL-D800C NAS Expansion – Quick Review

What you see is largely what you get here and although JBOD solutions are not for everyone, those that want one will be hard pushed to find better in 2020. The Performance benchmarks from the official site do lean heavily on SSD and RAID 0, which is far from commonplace, so expect fractionally more modest speeds, but if you have a decent RAID controller on-board or have an Intel Core or Xeon processor, then this might not present a problem. Otherwise, you can still always consider the TR series from QNAP for hardware RAID expansions or the TL SAS Port based series that arrives with external SAS connectors and a PCIe card to upgrade your NAS/PC/Mac system and achieve speeds of up to 5000MB/s in the right environment. Ultimately, this is a solid, if somewhat niche solution and if you are looking for a decent desktop JBOD enclosure this year, look no further!

SOFTWARE - 4/10
HARDWARE - 8/10
PERFORMANCE - 8/10
PRICE - 7/10
VALUE - 7/10


6.8
PROS
👍🏻Excellent Price Point
👍🏻Good Storage Potential
👍🏻Sturdy Design
👍🏻Easy to Use
👍🏻Client PC App available
👍🏻Fan and Noise Control Switches
CONS
👎🏻JBOD Only, though alternatives are available
👎🏻Almost ALL metal design, so noise might be a factor
👎🏻Connecting USB cable is not screw locked

QNAP TL-D800C NAS Expansion – Retail Packaging

The QNAP TL-D800C arrives in packaging not unlike a regular NAS. Whether this is just a move by the manufacturer to ensure that production costs are lower, or because they are balancing sales of this device in both NAS expansion AND traditional PC/Mac use is hard to pin down, but I am pleased to see that this device is not arriving in a bog-standard brown box, no label packaging as you would generally find from a purely functional piece of kit like an expansion enclosure.

The retail box is pretty big, to accommodate the sturdy foam packaging inside to protect this metal chassis NAS in transit, and the applied product label is pretty informative to the specs (a lot more than I would have expected in a JBOD case) and the TL-D800C is quite well presented in general for something that is more functional that fun!

Opening the box, we find that significant protection inside that protects this device from motion damage in transit. I have this debate alot(sad I know) with people about packaging materials in these devices and how I think a lot of brands do NOT take it seriously enough. Bottom line, if a forklift truck in a logistics hub skewers a retail box, NOTHING is protecting the contents, but the most common danger to computer hardware is shock/movement damage in transit. Too many brands think a cardboard framework inside the box is sufficient, but try to imagine it holding up when the box is dropped at an angle from 6 feet… then loaded back onto a lorry for the rest of its journey – the result, scrambled eggs!

The hard foam and spaced framework inside the TL-D800C box is something that QNAP should take a moment and be proud of and often overlooked.

Once you completely inbox the TL-D800C retail bow, you find all the bits and bobs you will need to use this NAS expansion (not including hard drives). These include:

It’s a fairly standard collection of components and as much as I would expect, but I will focus on a couple of bits that stand out.

One a plus note, the 8-Bay NAS Expansion arrives with 2 keys for locking/unlocking the individual SATA Bays, this prevents both accidental removal of a bay (more common than many would give it credit) as well as preventing theft of the media (far less likely in this context in my opinion). I am glad the TL-D800C can be Locke, as it shows that this was a consideration, but it does make my next point a little counter to that.

Now, the TL-D800C arrives with a USB-A to USB-C cable, which on the face of it is a good thing. USB C supported NAS drives are still pretty few and far between, so chances are that you will be expanding a USB-A ported NAS. Additionally, this cable does provide the 10Gb and 5Gbe bandwidth for USB 3.1 Gen 1 and Gen 2 as appropriate to your NAS, which will be good news to those looking at connecting with bigger and better desktop NAS.

However, something I am less impressed with is the length of the cable and the fact that it is not screw-locked. I know this is not something QNAP have featured in the build of their existing NAS devices, so there is a definite argument to not have this on the ‘NAS end’, but at the end connected to the TL-D800C itself, it is less understandable. The TL-D800C DOES arrive with a cable clip that attaches to the rear of the device, but it is not just as solid as a 2 part screw lock found on other eSATA connections. It is a very minor point, but one that seems like a half measure, given the inclusion of a cable clip and lockable trays to prevent accidental disconnection. However, this minor blip aside, I am overall please with the retail kit and accessories.

QNAP TL-D800C NAS Expansion – Design

Using a familiar 8-Bay metal chassis that we have seen in the likes of the TS-832X, TVS-872XT and TVS-872N, the QNAP TL-D800C external case is big but remarkably compact. It clearly lacks alot of the hardware features of the other 8-Bay devices mentioned (again, an expansion for just over £400 for 8 bays – what do you want, jam on it?) but it is possibly one of the most rugged desktop expansion chassis I have seen and sincerely hope the TR-108CT2 / TR-008T match this level of design quality for enterprise.

The TL-D800C NAS expansion arrives at 18.8cm × 32.9cm × 28.1cm in size, which is largely identical to the majority of QNAP 8-Bay NAS released in the last 2-3 years. This is an almost completely metal external chassis, which means it will generate a little more noise than some, as well as a reported 48.8W power utilization whilst in full access and 8 drives in a RAID. These factors will result in the TL-D800C being a little a pinch noise than smaller expansions like the TR-002 and TR-004, with a reported noise level of 26.2 db(A). So, not really designed for close proximity if you have issues with vibrations and noise – especially with more enterprise-grade NAS media like Seagate Ironwolf and WD Red over 10TB in capacity.

The system has multiple LEDs for denoting system activity as well, as well as on individual drives. The front-mounted LEDs on the side of the traditionally QNAP found LCD panel denote power, connectivity and general activity. Likewise, each bay has a 3 colour LED for denoting activity and health. Generally, it will either be green for good and red for not, but it will flash in accordance with that particular bay being accessed.

Each bay (as touched on earlier) has lockable trays that each allow the installation of 3.5″ and 2.5″ media. Given that current NAS hard drives can now be purchased at 16TB (Seagate Ironwolf), that means you have a potential 128TB of raw storage (pre-RAID).

The fact that each bay can be locked is a nice touch and certainly, something that I would recommend for an external storage device that may well have it’s RAID configuration being conducted externally and therefore a little more vulnerable to problems associated with unsafe disconnection of media. The trays themselves are hard plastic in design, which given the overall metal materials in the external chassis, will possibly assist reduced vibration noise. I know some users have had issues with plastic trays, favouring the metal ones as early gen NAS with plastic trays did not stand up well to heat. I can dispel this in modern NAS and pretty much all desktop NAS these days from top tier vendors used harder plastic with considerably higher heat resistance.

Removing a tray via its 2 part locking engagement shows us a familiar tray as used in other modern NAS devices from QNAP.

This is a tool-less, click and load tray that allows you to install any SATA 3.5″ media in seconds, as well as arriving with 2.5″ media (HDD and SSD) screw holes and screws if you wish to use more compact media. It is worth highlighting that as this device is a JBOD, you can create multiple RAID storage pools using smaller sets of drives (eg 8 bays, but 2x RAID 1, 1x RAID 5) that would let you install different media for each set, but this will push the CPU utilization more and likely negatively impact on your read/write performance.

Another area of concern that many users have about both NAS and NAS expansions is ventilation. Most NAS features active cooling measures in the form of rating fans, along with passive cooling in the form of heatsinks on chips and ventilation panels. The QNAP TL-D800S features this too and has a good degree of ways it manages to maintain a good performance temperature.

Taking a look at the base of the device shows us the four rubberized feet that suspend the TL-D800S a small distance from the desktop surface, as well as ventilation under each HDD bay.

QNAP TL-D800C NAS Expansion – Ports and Connections

The QNAP TL-D800C is much simpler than it’s NAS cousins and is practically unrecognizable in the sense of traditional ports. There are certainly some small common ground. For a start, this desktop 8-Bay NAS arrives with an internal 250W PSU, that is more than enough for this simple 8 SATA system.

It does seem to be alot of power for what is essentially a relatively brainless box, but alot of that power goes towards system stability, a key area of which is cooling. The QNAP TL-D800C has two rear-mounted cooling fans that will work in conjunction with all the available passive cooling to keep air flowing over the internal components and media

That said, in an all-metal chassis like this, along with the two rear fans, some users might be a little concerned about noise (especially given the 1metre USB cable) and for those users, the rear fans do arrive with a physical adjustment switch that allows you to increase or decrease the RPM as needed.

This physical control (given the lack of software on-chip, SoC) extends to more than the fans and there is even a switch to prevent beeping alerts from the device. This might seem risky for some, but many users like the option of silencing the occasional temperature, connection, reboot beep notifications and in a JBOD you are largely forced to use a physical switch to action this.

But of course of all the ports and connections that are available on the TL-D008C, the one that is the most important is the USB 3.1 Gen 2 Type C port. This is the means with which you are going to connect to the device and access the media there-in.

As mentioned, the TL-D800C uses 10Gbe USB 3.1 Gen 2 (AKA USB 3.2)  as it’s the maximum connection at 10GB/s (1000MB/s), however, if you are connecting this NAS expansion in conjunction with a USB 3.1 Gen 1 (AKA USB 3.0 or USB 3.2 Gen 1) port, then it will limit the transmission to 5Gb/s (Max 500MB/s). This is why the accessories pack contains a USB-C to USB-A cable. That said, it is still a non-screw locked cable, which I am a little sad about. That is not the only area where I was a teeny bit surprised. At a casual glance, you notice that there are two PCIe slots.

Is this an area where we might be able to install a RAID card? Or perhaps to install improved connections (SAS?) and have faster access? This is something that is present in newer generation expansion devices, such as the TL-D1600S. So, I decided to dig a little deeper into the chassis.

Removing the external chassis was pretty easy with the three rear screws, but sadly it immediately came apparent that the PCIe slots are not factored onto the main internal board, and are just a feature of this backplane.

However, the internal chassis DOES reveal that it is a very spacious casing, with plenty of potential for cooling airflow and efficiency. The system is mainly comprised of two main boards. One is the main 8 port SATA board that allows the connection of each media drive bay. This is then connected to another board that contains the controller. This does not rival a good RAID on chip, but still handles things on behalf of the connected host system well.

There are not many other surprises available to see inside the QNAP TL-D800C, as this is designed to be a JBOD solution where your connected host system will make the decisions.

What Kind of QNAP NAS Expansion Enclosures are there?

The range of QNAP expansion chassis can be broken down into 4 sections:

UX-XXXP and TX-XXXP Series = The old QNAP NAS expansion range, JBOD only and connected by either USB 3.0 Type-A (UX) or Thunderbolt 2 (TX).

TL-XXXXC = USB 3.1 Gen 2 Enabled Storage Expansion, delivering connectivity to 8-12 Drives at upto 10Gb/s. However, it is JBOD only and requires the NAS, Windows PC  or Mac System to create a RAID Space on the device

TR-XXX = USB 3.1 Gen 1 and USB 3.1 Gen 2 Hardware RAID Enabled Storage Expansion, delivering connectivity to 2-4 Drives at upto 5-10Gb/s. Can be used by a NAS, Windows PC  or Mac System to create a RAID Space on the device . Additionally, there Thunderbolt 3 enabled additions to this range in the form of the QNAP TR-104C, TR-106C and TR-108C2T that also support USB 3.1 Gen 2.

TL-XXXXS = SAS external enabled Expansion Storage, supporting SATA based drives, delivering connectivity to 4-16 Drives at upto 1-6GB/s (yes, Gigabytes, so 1000-6000MB/s). Additionally, each device in this range arrives with a QNAP QXG PCIe Card and cables that can be installed in a NAS, Windows PC  or Mac System system, so both the QNAP Expansion and Host system can communicate as fast as possible. Finally, the highest tier in this range, the TL-R1600S features both a PCIe slot for adding a RAID card, as well as 4 dedicated SSD bays.

QNAP TL-D800C NAS Expansion – Conclusion

The TL-D800C from QNAP is a solid enough product and if you are looking for the simplest means to add a whole bunch more hard drives to your existing NAS system, further bolstering your available storage, it is a great product. It may seem a little underwhelming, especially when compared to the TR-002, TR-004, TR-104C and TR-106C released and revealed in the last year or so, but then this is not aimed at replacing those expansion solutions. The TL-D800C is a solution to a different kind of problem and one that there is still very much a market for, even in 2020. Yes, it does seem to rely on the host NAS system doing all the work, but the clear fact that decades after the invention of RAID configurations, there is still a market for JBOD only goes to show that this rather acquired taste of an enclosure is exactly what THAT market wants. The Performance benchmarks from the official site do lean heavily on SSD and RAID 0, which is far from commonplace, so expect fractionally more modest speeds, but if you have a decent RAID controller on-board or have an Intel Core or Xeon processor, then this might not present a problem. Otherwise, you can still always consider the TR series from QNAP for hardware RAID expansions or the TL SAS Port based series that arrives with external SAS connectors and a PCIe card to upgrade your NAS/PC/Mac system and achieve speeds of up to 5000MB/s in the right environment. Ultimately, this is a solid, if somewhat niche solution and if you are looking for a decent desktop JBOD enclosure this year, look no further!

QNAP TL-D800C Expansion Pros QNAP TL-D800C Expansion Pros
  • Excellent Price Point
  • Good Storage Potential
  • Sturdy Design
  • Easy to Use
  • Client PC App available
  • Fan and Noise Control Switches
  • JBOD Only, though alternatives are available
  • Almost ALL metal design, so noise might be a factor
  • Connecting USB cable is not screw locked

The QNAP TL-D800C NAS Expansion is available to Buy now via that link below:

I hope you found this guide helpful and it made the complex range of QNAP NAS Expansions in 2020/2021 alot easier to understand. If you are still lost in what you need, or just want a few pointers on the right solution for your needs, fire me over a message below in my completely free and community supported Free Advice section. It’s just me on there, but I will get around to answering all enquires!

Click to Learn about the best 4-Bay NAS from QNAP

📧 SUBSCRIBE TO OUR NEWSLETTER 🔔


    🔒 Join Inner Circle

    Get an alert every time something gets added to this specific article!


    Want to follow specific category? 📧 Subscribe

    This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

    Need Advice on Data Storage from an Expert?

    Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry.

      By clicking SEND you accept this Privacy Policy
      Question will be added on Q&A forum. You will receive an email from us when someone replies to it.
      🔒Private Fast Track Message (1-24Hours)

      TRY CHAT Terms and Conditions
      If you like this service, please consider supporting us. We use affiliate links on the blog allowing NAScompares information and advice service to be free of charge to you.Anything you purchase on the day you click on our links will generate a small commission which isused to run the website. Here is a link for Amazon and B&H.You can also get me a ☕ Ko-fi or old school Paypal. Thanks!To find out more about how to support this advice service check HEREIf you need to fix or configure a NAS, check Fiver Have you thought about helping others with your knowledge? Find Instructions Here  
       
      Or support us by using our affiliate links on Amazon UK and Amazon US
          
       
      Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.

      ☕ WE LOVE COFFEE ☕

        This description contains links to Amazon. These links will take you to some of the products mentioned in today’s video. As an Amazon Associate, I earn from qualifying purchases

       

      locked content ko-fi subscribe

      DISCUSS with others your opinion about this subject.
      ASK questions to NAS community
      SHARE more details what you have found on this subject
      CONTRIBUTE with your own article or review. Click HERE
      IMPROVE this niche ecosystem, let us know what to change/fix on this site
      EARN KO-FI Share your knowledge with others and get paid for it! Click HERE

      ASK YOUR QUESTIONS HERE!

      3 thoughts on “The QNAP TL-D800C Hardware Review

      1. Old video, but I’ve got a question (noob here). Can the TL-D800C be used as a simple hard drive enclosure as-is? As-in, slot in 8 drives in it then plug the USB cable onto a Windows 10 PC and the PC would detect those drives like external/internal hard drives?

        Asking because I’ve been looking for a mass storage solution but would just like it to be simple via USB and where I can just add drives when it gets full. I don’t really want to go through all the trouble of setting up RAID setups or network arrays as it’s mostly for personal use anyway, but I have a lot of stuff (mainly backups of my games and media), and I would like to reduce my external HDD clutter.
        REPLY ON YOUTUBE

      2. I have a QNAP TVS1282T3, and am filled up with no data space with in all my 8TB Reds that are in Raid 6 Configuration. I was told on the phone by a QNAP Customer Service guy back in December when I was considering the TX-800P, that I would have to make a separate pool in that 8 bay enclosure, and would have to set up Raid 6 in that pool of 8 drives in the expansion unit, and thus would lose 2 more drives worth of data, as they are parity drives. In your article here for the new QNAP TL-D800C, you say “it is JBOD only and requires the NAS, Windows PC or Mac System to create a RAID Space on the device or extend an existing RAID onto it”. That last half of your quote after the word “or” is what I’m interested in, and goes against what the QNAP guy told me, I’m hoping. So, could I add this expansion box, and use the two parity drives in the 1282T3 that I would hook this up to, and I would get the use of all 8 drives in the expansion box, as one pool together between the two boxes, so I don’t have to have two separate pools of Raid 6, one in each box? Please explain what you know about “extend an existing Raid onto it”.
        And secondly, since I want to daisy-chain multiple expansion boxes together with my 1282T3, as I could have with the discontinued QNAP TX-800P, I know this TL-D800C doesn’t allow you to do this (due to only one USBC connection), and I would need to wait for the TR-108C2T. Would I be able to keep expanding my Raid-6 setup with multiple expansion boxes as one big pool and only losing the data storage of the two parity drives, or would I need to make a separate pool of Raid-6 setup drives with each expansion box I add, plus, the original Raid-6 pool in my TVS1282T3?