RAM upgrade for RS820RP+, RS820+, DS2419+, DS1819+, DS1618+, DVA3219

RAM upgrade for RS820RP+, RS820+, DS2419+, DS1819+, DS1618+, DVA3219

 

Non-ECC SO-DIMM

D4NESO-2666-4G4GB

DDR4-2666 non-ECC unbuffered SO-DIMM
EAN: 4711174723669

US UKĀ 

Applied Models: RS820RP+, RS820+, DS2419+, DS1819+, DS1618+, DVA3219

Crucial alternative:

8GB

Crucial CT8G4SFS8266 8 GB (DDR4, 2666 MT/s, PC4-21300, Single Rank x8, SODIMM, 260-Pin) Memory

UKĀ  Ā USA

16GB – slower but should work

Crucial 16GB Single DDR4 2400 MT/s (PC4-19200) DR x8 SODIMM 260-Pin for Mac – CT16G4S24AM

UKĀ  USA

 

ECC SO-DIMM

D4ECSO-2666-16G16GB

DDR4-2666 ECC unbuffered SO-DIMM
EAN: 4711174723676

Applied Models*: FS1018, DS3617xs, DS3018xs, DS2419+, DS1819+, DS1618+, RS820RP+, RS820+, DVA3219

Synology D4ECSO-2666-16G memory module 16 GB DDR4 2666 MHz ECC

Notes:
___

  • RS820+/RS820RP+ does not support the ECC feature, regardless of whether the expansion memory is ECC or non-ECC.

Alternatives:

Crucial CT16G4TFD8266 16GB DDR4 2666 MHz ECC Memory Module (16GB, 1X 16GB, DDR4, 2666MHz, 260-pin SO-DIMM)

UKĀ  USA

Best alternative RAM will be from Crucial.Ā  It is important to not mix different frequency/ speed RAM modules. You need to replace both RAM sticks in some cases to match this.

Add a RAM Module on DiskStation
The optional Synology DDR4 RAM module is designed for DiskStation memory expansion. Follow the steps
below to install, check, or remove a RAM module on your DiskStation.
To install the RAM module:
1 Press and hold the power button until you hear a beep sound to shut down your DiskStation. Disconnect all
cables from your DiskStation to prevent any possible damage.
2 The RAM modules are located at the bottom of DS1618+.
3 Remove the 2 screws that secure the bottom lid. Lift off the lid and place it to the side. You will see one 4GB
module pre-installed.

4 Insert the new memory module in the slot:
a Align the notch on the gold edge of the module with the notch in the memory slot.
b Tilt the card and insert the module into the slot. Make sure the module is properly inserted.
c Push the memory module with moderate pressure into the memory slot until you hear a click.

5 Replace the bottom lid. Replace and tighten the 2 screws you removed in step 3.
6 Reconnect the cables you removed in step 1, and then press and hold the power button to turn on your
DiskStation.

To make sure DiskStation recognizes the new memory capacity:

1 Install DiskStation Manager (DSM). (See the next chapter for more information.)
2 Log in to DSM as admin or a user belonging to the administrators group.
3 Check Total Physical Memory in Control Panel > Info Center.
If your DiskStation does not recognize the memory or does not start up successfully, confirm that the memory is
installed correctly.

To remove the RAM Module:

1 Follow step 1 to 3 of the “To install the RAM module” section to shut down your DiskStation, disconnect the
cables, and then remove the bottom lid.
2 Push the levers on both sides of the memory module outwards. The module will be released from the slot.
3 Hold the memory module by its notches and remove it from the slot.

4 Replace the bottom lid. Replace and tighten the screws removed in step 1.
5 Reconnect the cables removed in step 1. Now, you may turn on your DiskStation.

 

 

locked content ko-fi subscribe

DISCUSS with others your opinion about this subject.
ASK questions to NAS community
SHARE more details what you have found on this subject
CONTRIBUTE with your own article or review. Click HERE
IMPROVE this niche ecosystem, let us know what to change/fix on this site
EARN KO-FI Share your knowledge with others and get paid for it! Click HERE

ASK YOUR QUESTIONS HERE!

3 thoughts on “RAM upgrade for RS820RP+, RS820+, DS2419+, DS1819+, DS1618+, DVA3219

  1. Ah x2, according to this page the Crucial ct8g4sfs8266 should work with a DS1819+ but I still get memory warnings….. Sigh.
    IT seems as if these recommendations cannot be trusted anymore which is really sad.

  2. Ah, I just realized I experienced a copy-n-paste fault when ordering this mem. I managed to order the same mem model as for my DS1621+….
    Well, nice to know it works even in DS1819+ even though mem waring shows.
    So, back to the drawing-board and do it right this time.

  3. Are any/all of the above mentioned memory types CONFIRMED working, without the memory warning, in DSM 7.x and in the mentioned models?
    I ask since I got a Crucial CT16G4SFD8266 16Gb (mentioned in another page in here) to my DS1819+, running on DSM 7.0.1, but it pop-ups the memory warning….
    AND, it doesn’t seem to show directly, it took a while before it popped up.
    Seem to be working but not ideal to have the warning everytime it boots.
    None of the other upgrades I have done have any warnings/pop-ups (yet) and I’ve done my fair share of them. DS216+, DS216+II, DS218+, DS718+, DS1515+, DS1815+, DS1621+, no warnings. So, when this started…