RAM upgrade for Asustor Nimbustor 2&4 AS5304T / AS5202T

RAM upgrade for Asustor Nimbustor 2&4 AS5304T / AS5202T

After watching your video about 16GB upgrade, wondering if the J4105 Celeron can handle frequencies above 2400Mhz.

Looking at Crucial Ballistix 3200Mhz or Kingston HyperX 2666Mhz

The specs say 2400 MT/s. But you can always experiment. If it doesn’t work you can always return.

Here is Asustor compatibility list:

 

ASUSTOR DDR4 SDRAM AS-2GD4 2G For AS 52/53 series DDR4-2400, 1.2V, 260Pin SO-DIMM
ASUSTOR DDR4 SDRAM AS-4GD4 4G For AS 52/53 series DDR4-2400, 1.2V, 260Pin SO-DIMM
Crucial DDR4 SDRAM CT2K102464BF186D 8G For AS 52/53 series
DDR3-1866, 1.35V, 260Pin SO-DIMM
Crucial DDR4 SDRAM CT8G4SFS824A 8G For AS 52/53 series
DDR4-2400, 1.2V, 260Pin SO-DIMM
Hynix DDR4 SDRAM HMA81GS6AFR8N-UH 8G For AS 53 series DDR4-2400, 1.2V, 260Pin SO-DIMM

 

And Crucial RAM upgrade options:

Crucial 4GB DDR4-2400 SODIMM
CT4G4SFS824A
Configuration ID: CT15395563
DDR4 PC4-19200 • CL=17 • Single Ranked • x8 based • Unbuffered • NON-ECC • DDR4-2400 • 1.2V • 512Meg x 64 •

Crucial 8GB Kit (2 x 4GB) DDR4-2400 SODIMM
CT2K4G4SFS824A
Configuration ID: CT15395537
DDR4 PC4-19200 • CL=17 • Single Ranked • x8 based • Unbuffered • NON-ECC • DDR4-2400 • 1.2V • 512Meg x 64 •

 

 

Crucial 4GB DDR4-2666 SODIMM
CT4G4SFS8266
Configuration ID: CT15395548
DDR4 PC4-21300 • CL=19 • Single Ranked • x8 based • Unbuffered • NON-ECC • DDR4-2666 • 1.2V • 512Meg x 64 •

Crucial 4GB DDR4-2666 SODIMM
CT4G4SFS6266
Configuration ID: CT15395559
DDR4 PC4-21300 • CL=19 • Single Ranked • x16 based • Unbuffered • NON-ECC • DDR4-2666 • 1.2V • 512Meg x 64 •

Crucial 8GB Kit (2 x 4GB) DDR4-2666 SODIMM
CT2K4G4SFS8266
Configuration ID: CT15395535
DDR4 PC4-21300 • CL=19 • Single Ranked • x8 based • Unbuffered • NON-ECC • DDR4-2666 • 1.2V • 512Meg x 64

Crucial 8GB Kit (2 x 4GB) DDR4-2666 SODIMM
CT2K4G4SFS6266
Configuration ID: CT15395545
DDR4 PC4-21300 • CL=19 • Single Ranked • x16 based • Unbuffered • NON-ECC • DDR4-2666 • 1.2V • 512Meg x 64 •

 

 

Crucial 4GB DDR4-3200 SODIMM
CT4G4SFS632A
Configuration ID: CT15395564
DDR4 PC4-25600 • CL=22 • Single Ranked • x16 based • Unbuffered • NON-ECC • DDR4-3200 • 1.2V • 512Meg x 64 •

Crucial 8GB Kit (2 x 4GB) DDR4-3200 SODIMM
CT2K4G4SFS632A
Configuration ID: CT15395529
DDR4 PC4-25600 • CL=22 • Single Ranked • x16 based • Unbuffered • NON-ECC • DDR4-3200 • 1.2V • 512Meg x 64 •

 

 

Here is how to do it:

 

Use a screwdriver to loosen the three screws found on the rear of the NAS as shown
in the illustration.

Grip the cover from both sides with two hands and then gently push it back to
remove it from the chassis.

 

Installing Memory
Note: When installing a single memory module, please ensure that it is the same size as the built-in
memory module (1GB/2GB). When installing two memory modules, please ensure that they are the
same size and ideally use the same type of RAM for both memory slots. The maximum supported
memory is 8GB combined.
To install the first memory module, follow the steps outlined below.
• When inserting the memory module into the empty slot, please make sure to align the notches on
the module with the notches in the slot.

 

 

Diagonally slide in the memory module (as shown in the illustration) making sure that the memory
module’s connectors are fully inserted into the slot.

Using two fingers, carefully push down and then back on the memory module until it clicks into
place. You should be able to hear an audible “click”.

To install the second memory module, continue with the steps outlined below.
• Locate the slot for the built-in memory as shown in the graphic below.

Release the ejector clips by gently pulling them out to the sides and then remove the built-in
memory module.

When inserting the memory module into the empty slot, please make sure to align the notches on
the module with the notches in the slot. Diagonally slide in the memory module (as shown in the
illustration) making sure that the memory module’s connectors are fully inserted into the slot.
Using two fingers, carefully push down and then back on the memory module until it clicks into
place. You should be able to hear an audible “click”.

 

 

Replace the cover and tighten the three screws that were removed previously

 

 

 

 

 

locked content ko-fi subscribe

DISCUSS with others your opinion about this subject.
ASK questions to NAS community
SHARE more details what you have found on this subject
CONTRIBUTE with your own article or review. Click HERE
IMPROVE this niche ecosystem, let us know what to change/fix on this site
EARN KO-FI Share your knowledge with others and get paid for it! Click HERE

ASK YOUR QUESTIONS HERE!

One thought on “RAM upgrade for Asustor Nimbustor 2&4 AS5304T / AS5202T