Seagate Ironwolf 525 vs 510 NAS NVMe SSD Comparison

Comparing the Seagate Ironwolf 510 vs Seagate Ironwolf 525 – Which Should You Use in Your NAS?

The Seagate Ironwolf series of NAS media has been around for a few years now and what started as a rebranding of their ‘NAS’ labelled series has now become a multi-tiered series of Hard drives and SSDs. Recently Seagate introduced a new entry into their Ironwolf SSD series with the 525 NVMe SSD. Presented as a higher bandwidth supporting alternative NVMe SSD to the Ironwolf 510 (released back in March 2020), the Ironwolf 525 is a PCIe Gen 4 NVMe SSD that arrives in slightly larger capacities, much higher performance and still allowing backwards compatibility with PCIe Gen 3 m.2 slots in your NAS. So, with the release of this newer, faster and widely supported NVMe SSD, should you still consider buying the Seagate Ironwolf 510 at all? Well, yes! The older Ironwolf 510 still arrives with a few rather unique architecture and design choices that are not available in the Ironwolf 525 and today I want to take a close look at each of these NAS focused SSDs and help you decide which one you should buy for your NAS drive in 2021/2022.

Important – It is worth remembering that the two SSDs in today’s comparison are m.2 NVMe in architecture and although PCIe Gen 4 is compatible with Gen 3 and old, they will not suitable for NAS drives with M.2 SATA connections. We have seen more modern NAS systems released in the last few years abandon m.2 SATA in favour of its PCIe counterpart, but Seagate provides SATA alternatives in their Ironwolf series. Examples of SATA SSDs for NAS can be found HERE on Amazon. Additionally, it is worth highlighting for the later stages of testing in this comparison, I was only able to obtain the 240GB model of the Ironwolf 510, so although the performance shown is low (and much lower than the Ironwolf 525 as expected in most cases) it is particularly low because the test drive is the 240GB Model. Please follow the official performance specifications in the table below for a better indication of how comparable capacity drives would differ.

How do the Seagate Ironwolf 525 and Seagate Ironwolf 510 SSD Compare on Specs?

Seagate are well known for their wide ranges of hard drive and SSD media, as well as both being pioneers of NAS server focused SSDs for caching and flash storage. Although SSDs are all built to a similar ground-level architecture, they will often have their later development shifted in favour of a specific targetted use. This is not a big surprise and much like the cutlery in your kitchen draw, they might be similar but one tool is much better at some tasks than others – ever tried using a spreading butter with a meat-claver? Or stirring tea with a ladle? The Seagate Ironwolf 525 and Seagate Ironwolf 510 SSD are NAS targetted and although the performance is good, the true stand out factor in this design is the durability of the drive. SSDs for use in NAS systems will in most cases be used for caching and that means a very frequent turnover (i.e. data wrote, updated, deleted, repeat) daily as the demands of client users and devices change. Both of these SSDs arrive with a high level of durability and workload rating, but the Seagate Ironwolf 510 and Seagate Ironwolf 525 definitely have differing ideas of preliminary architecture and what that price tag is being spent on. Let’s look at the shared base-level SSD architecture of each SSD (available on every capacity):

Below Specifications are taken from official brand sources, data sheets and reputable sources (real-world tests we performed ourselves are a little lower in the article):

Specifications

Seagate IronWolf 525

Released September 2021

Seagate IronWolf 510

Released March 2020

Warranty 5yr + 3yr Rescue 5yr + 3yr Rescue
MTBF/MTTF 1800000 1800000
PCIe Generation PCIe Gen 4×4 PCIe Gen 3×4
NVMe Rev NVMe 1.3 NVMe 1.3
NAND Kioxia BiCS 4 96L 3D TLC NAND Kioxia BiCS3 64L TLC
Controller PS5016 SSD Controller PS5012-E12DC

Seagate uses 3rd party controllers and NAND manufacturers for the most part in their ranges, but are still generally quite top tier providers. The release time difference between the Seagate Ironwolf 510 and Seagate Ironwolf 525 makes an impressive difference here in terms of the hardware on offer on either SSD, with the more recently released Seagate Ironwolf 525 having notably superior connectivity, NAND quality and overall performance. Both Seagate Ironwolf SSDs features 3 years of forensic level data recovery services though (which caching NAS users might want to have in the event of ‘trapped data’ during write caching operations and a critical system failure/power-cut) which is very unique to the brand. However, overall the Seagate Ironwolf 525 has the superior architecture here. Below is how the building blocks of the Seagate Ironwolf 525 and Seagate Ironwolf 510 result in throughput, IOPS and Durability at each capacity tier (based on officially provided figures):

240/250GB

Seagate IronWolf 525

Released September 2021

N/A

Seagate IronWolf 510

Released March 2020

ZP240NM30011 – $69

Sequential Read (Max, MB/s), 128 KB N/A 2,450MB
Sequential Write (Max, MB/s), 128 KB N/A 290MB
480/500GB ZP500NM30002 – $99 ZP480NM30011 – $119
Sequential Read (Max, MB/s), 128 KB 5000MB / 3400MB 2,650MB
Sequential Write (Max, MB/s), 128 KB 2500MB / 2500MB 600MB
960/1000GB ZP1000NM30002 – $179 ZP960NM30011 – $209
Sequential Read (Max, MB/s), 128 KB 5000MB / 3400MB 3,150MB
Sequential Write (Max, MB/s), 128 KB 4400MB / 3200MB 1,000MB
1920/2000GB ZP2000NM30002 – $369 ZP1920NM30011 – $409
Sequential Read (Max, MB/s), 128 KB 5000MB / 3400MB 3,150MB
Sequential Write (Max, MB/s), 128 KB 4400MB / 3200MB 850MB
3840/4000GB N/A N/A
Sequential Read (Max, MB/s), 128 KB N/A N/A
Sequential Write (Max, MB/s), 128 KB N/A N/A
240/250GB N/A ZP240NM30011 – $69
Random Read (Max, IOPS), 4 KB QD32 N/A 100K
Random Write (Max, IOPS), 4 KB QD32 N/A 12K
2480/500GB ZP500NM30002 – $99 ZP480NM30011 – $119
Random Read (Max, IOPS), 4 KB QD32 420K / 420K 193K
Random Write (Max, IOPS), 4 KB QD32 630K / 550K 20K
960/1000GB ZP1000NM30002 – $179 ZP960NM30011 – $209
Random Read (Max, IOPS), 4 KB QD32 760K / 640K 345K
Random Write (Max, IOPS), 4 KB QD32 700K / 565K 28K
1920/2000GB ZP2000NM30002 – $369 ZP1920NM30011 – $409
Random Read (Max, IOPS), 4 KB QD32 740K / 640K 270K
Random Write (Max, IOPS), 4 KB QD32 700K / 565K 25K
3840/4000GB N/A N/A
Random Read (Max, IOPS), 4 KB QD32 N/A N/A
Random Write (Max, IOPS), 4 KB QD32 N/A N/A
Heatsink Option No No
TBW Rating 700/1400/2800 435/875/1750/3500
DWPD Rating 0.7 DWPD 0.9-1.0 DWPD
Note – BLUE Text is the Seagate Ironwolf 525 on a PCIe Gen 3×4 Slot

Overall, it should come as no surprise that the Seagate Ironwolf 525 is the notable leader here in practically all official benchmarks over the slightly older Seagate Ironwolf 510 SSD, thanks to that improved architecture. Most notably in write performance and IOPS in general, it had a clear lead even in the lowest available capacities. Of course, these are officially provided performance figures and represent maximums based on the highest available hardware at the time of release. Let’s take a look at how these two SSDs compare in our own tests.

How Did the Seagate Ironwolf 510 and Seagate Ironwolf 525 Compare in OUR Tests?

Moving away from the official performance stats provided by WD and Seagate, I wanted to see how the Seagate Ironwolf 510 and 525 compared in my own tests. Testing of these two SSDs will be broken down into 3 main parts, a CrystalDisk Benchmark test, Atto Disk Benchmark Test and an AJA media test. In each test, the SSD was in the 2nd storage slot (i.e not the OS drive). Each test was conducted three times and the system was left for 1 minute between tests to allow the SSD time to stabilize. The specifications of the test machine are:

Test Machine:

  • Windows 10 Pro Desktop System
  • Intel i5 11400 Rocket Lake – 6-Core 2.6/4.4Ghz
  • 16GB DDR4 2666MHz Memory
  • Intel B560M mATX Motherboard
  • OS Storage, Seagate Firecuda 120 SSD
  • Test SSD connected to Secondary PCIe Gen 4×4 M.2 Slot

CrystalDisk 1GB Test File – Read, Write, 70/30% Mixed and IOPS Performance

CrystalDisk is still highly regarded as one of the most reliable tools for measuring storage media performance. Though it does create somewhat high-end results that may not be truly indicative of your own real-world setup, it can be used to display maximum potential throughput and IOPs at each tier. The first test for the Seagate Ionwolf 510 and Seagate Ironwolf 525 was on a 1GB test file:

Seagate Ironwolf 525

Seagate Ironwolf 510 SSD

Overall Winner: The Seagate Ironwolf 525

CrystalDisk 4GB Test File – Read, Write, 70/30% Mixed and IOPS Performance

The next test was to perform the same parameters in CrystalDisk on the Seagate Ironwolf 525 and Seagate Ironwolf 510, but this time with a 4GB test file (larger files may result in higher sequential performance, but lower comparative IOPS):

Seagate Ironwolf 525

Seagate Ironwolf 510 SSD

Overall Winner: The Seagate Ironwolf 525

ATTO DiskBenchmark 256MB Test File – Read, Write

Switching things up, I then moved testing the Seagate Ironwolf 510 and Seagate Ironwolf 525 over to ATTO disk benchmark. A far more detailed tool that spreads performance testing over different file and block sizes. I started with the smallest ‘full range’ test file of 256MB (as smaller would reduce the range of block sizes). Here is how each SSD compared:

Seagate Ironwolf 525

Seagate Ironwolf 510 SSD

Overall Winner: The Seagate Ironwolf 525

ATTO DiskBenchmark 4GB Test File – Read, Write

Sticking with ATTO DiskBenchmark, I then moved the testing of the Seagate Ironwolf 525 and Seagate Ironwolf 510 onto a x16 bigger test file of 4GB. This would certainly shift where the peaks in performance would sit and hopefully produce a clearer disparity between these two SSDs:

Seagate Ironwolf 525

Seagate Ironwolf 510 SSD

Overall Winner: The Seagate Ironwolf 525

AJA 1080i Media Test 1GB Test File – Read, Write

I then switched to AJA, a popular media testing tool for video formats. Most SSDs will suffer over-saturated Memory/DRAM/SDRAM as sustained large file tests go on. The 1GB file test of AJA on the Seagate Ironwolf 525 and Seagate Ironwolf 510 is still a small enough value not to be a problem though and we chiefly focused on the disk playback/reads graph to see how they compared in peak performance and also throughout the transfer:

Seagate Ironwolf 525

Seagate Ironwolf 510 SSD

Overall Winner: The Seagate Ironwolf 525

AJA 1080i Media Test 16GB Test File – Read, Write

Then we used a much, MUCH heavier test in AJA of 16GB on the Seagate Ironwolf 510 and Seagate Ironwolf 525. Unsurprisingly this can often overflow the SSD cache/memory on board and result in a dip in performance as the SSD bottlenecks internally. So, when conducting this test, we are looking at peak performance AND how long the SSD maintained that performance before a potential dip. Here is how these two SSD compared:

Seagate Ironwolf 525

Seagate Ironwolf 510 SSD

Overall Winner: The Seagate Ironwolf 525

Seagate Ironwolf 525 vs Seagate Ironwolf 510 SSD – The Results

It is probably no surprise that the Seagate Ironwolf 525 is the better drive overall. With performance in throughput and IOPS that outshine the Ironwolf 510 in both Read and Write on a PCIe Gen 3 m.2 slot,  then upping the ante considerably by allowing 2-3x that performance via a PCIe 4 M.2 Connection. That said, the adoption of PCIe 4 x4 as the connection of choice in a NAS is currently very low indeed, largely down to the large availability of PCIe 3 SSDs in the market AND the simply fact that manufacturers would need to dedicate notably more CPU PCIe Lanes to a Gen 4 connection than they would a Gen 3 (lanes that might be better used in improved NAS external connectivity or other hardware services). Additionally, the Seagate Ironwolf 510 has higher durability in all capacities, as well as a smaller 240GB capacity for those considering caching on much smaller systems/HDDs. The Seagate Ironwolf 525 is still the better SSD choice over the Ironwolf, but if you see it at a bargain price, have intensive data re-writes in mind or are looking for a smaller SSD, it’s still a viable option. And don’t forget, both SSDs include that 3 year Rescue Data Recovery service and Seagate Ironwolf Health Management that is accessible via your NAS Storage Manager (supported on Synology, QNAP, Asustor and more).

The Seagate Ironwolf 525 NVMe SSD Wins on:

  • Higher Performance (Read & Write), even in a PCIe Gen 3 Slot
  • Supports PCIe Gen 4 M.2 NVMe SSD Slots
  • Better Sustained Performance
  • Massively Higher IOPS ratings (Read and Write)
  • Takes Advantage of a several gen higher Phison Controller

The Seagate Ironwolf 510 NVMe SSD Wins on:

  • Higher Durability at 0.9-1.0 DWPD on all Capacities (IW 525 t 0.7 DWPD)
  • Smaller 240GB Capacity Available
  • PCIe Gen 3 is still at more than 95% adoption on NAS systems compared with PCIe 4
  • Been available longer, so might have more flexible pricing online

 

📧 SUBSCRIBE TO OUR NEWSLETTER 🔔


    🔒 Join Inner Circle

    Get an alert every time something gets added to this specific article!


    Want to follow specific category? 📧 Subscribe

    This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

    Need Advice on Data Storage from an Expert?

    Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry.

      By clicking SEND you accept this Privacy Policy
      Question will be added on Q&A forum. You will receive an email from us when someone replies to it.
      🔒Private Fast Track Message (1-24Hours)

      TRY CHAT Terms and Conditions
      If you like this service, please consider supporting us. We use affiliate links on the blog allowing NAScompares information and advice service to be free of charge to you.Anything you purchase on the day you click on our links will generate a small commission which isused to run the website. Here is a link for Amazon and B&H.You can also get me a ☕ Ko-fi or old school Paypal. Thanks!To find out more about how to support this advice service check HEREIf you need to fix or configure a NAS, check Fiver Have you thought about helping others with your knowledge? Find Instructions Here  
       
      Or support us by using our affiliate links on Amazon UK and Amazon US
          
       
      Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.

      ☕ WE LOVE COFFEE ☕

       

       


      DISCUSS with others your opinion about this subject.
      ASK questions to NAS community
      SHARE more details what you have found on this subject
      CONTRIBUTE with your own article or review. Click HERE
      IMPROVE this niche ecosystem, let us know what to change/fix on this site
      EARN KO-FI Share your knowledge with others and get paid for it! Click HERE

      3 thoughts on “Seagate Ironwolf 525 vs 510 NAS NVMe SSD Comparison

      1. I’ve just had to replace my first drive in my QNAP NAS. I’ve watched the videos on it, it’s simple. Take the drive out, put new one in and the NAS should then sort itself out automatically…..but I don’t see it doing anything and I still have the warning that it’s degraded and I don’t see where to correct this. How can I tell if it’s fixing itself? If it isn’t, how do I tell it to fix itself?
        REPLY ON YOUTUBE

      Comments are closed.