The QNAP TS-133 NAS Drive Review
The QNAP TS-133 is a new NAS, sure, but there have been ALOT of these systems for a while now and why should you care about this one? It’s a valid question. Although network-attached storage (NAS) has been around for quite a number of years, the average buyer has diversified quite dramatically. NAS systems once started life as mini servers for professionals and small/medium business (SMB) users to allow them to have their very own alternative to smaller subscription business cloud systems. However, when NAS first started becoming more home-user-friendly, a huge range of solutions quickly developed that were tailored to different user requirements, budgets and scales. One area of NAS that still continues to have a moderate (if slightly entry-level) following is that of single bay (AKA 1-Bay) NAS drives that serve as the first step for many into owning their own private server. Arriving at a considerably more affordable price point than their larger, RAID enabled brothers and sisters, 1-Bay NAS drives such as the QNAP TS-133 provide a base level introduction to the software and services available in a NAS, whilst streamlining the hardware for efficiency. Many might argue that you can just buy a bigger and more powerful NAS, then just install a single HDD, but those users would be rather missing the point. Today I want to review the QNAP TS-133 NAS drive, Discuss design, hardware, what it can do and what it can’t do. Right now, at the start of 2022, the QNAP TS-133 is the most powerful 1-Bay NAS that you can buy commercially (again, in the context of 1 HDD NAS systems) but arrives a pinch more expensive than most. So, let’s review the TS-133 NAS and decide whether it deserves your data in 2022/2023.
Hardware Highlights:
- ARM 4-core Cortex-A55 1.8GHz processor
- 2GB DDR4 (Max)
- 2x SATA HDD/SSD Bay
- Top Loaded Drive Injection
- 1x RJ45 1GbE
- 1x USB 3.2 Gen 1
- 1x USB 2.0
- Support of the USB-to-5GbE Adapter
- Low Noise single 80mm Fan
- 36W External PSU and Reported 2.74/7.32W Power Use (Idle/Active)
- 7.38 × 2.6 × 6.2 inch Chassis Size
QNAP TS-133 NAS Review – Quick Conclusion
As long as you keep your feet on the ground a little and stay realistic, the QNAP TS-133 NAS Drive is indeed a very impressive piece of kit. We are talking about a combined hardware and software solution that you can purchase with a 4TB drive from the likes of Seagate or WD inside all in for a little over $200. It can run plex media server, it has surveillance software included in QVR Elite, AI-powered photo recognition (with the system featuring a dedicated AI engine for these tasks), multi-tiered backup handing in Hybrid Backup Sync 3, host a DLNA media server, connect and synchronize with cloud services in a bunch of ways, access to a bunch of tailored mobile apps and a whole lot of other services that would take too long to mention. Also, the TS-133 NAS is the first system in the commercial NAS market to feature this new Cortex A55 processor, as well as twice (and in some cases) four times the memory of alternative systems in the same tier with it’s 2GB DDR4 RAM. As long as you have realistic expectations about how busy you are going to be, how hard you intend to push the device and how much you expect it to do at any one time, I think the QNAP TS-133 NAS is easily the most powerful and capable 1-Bay NAS in the market to buy right now. The non-upgradable memory is a pain, the lack of 2.5GbE is perplexing and the continued appearance of USB 2.0 is a tad infuriating, but the TS-133 seemingly makes up for it with a wide variety of applications supported, a remarkably subtle and discreet deployment and in the hands of the right low-level user, this might well be the best NAS QNAP have produced in the value tier for years!
| Where to Buy a Product | |||
 |
     |
   |
VISIT RETAILER ➤ |
 |
|
|
VISIT RETAILER ➤ |
 |
|
|
VISIT RETAILER ➤ |
 |
|
|
VISIT RETAILER ➤ |
 |
|
|
VISIT RETAILER ➤ |
 QNAP TS-133-US 1 Bay Affordable Desktop NAS with ARM Cortex-A55 Quad-core Proces Amazon  These Offers are Checked Daily
|
QNAP TS-133 NAS Review – PACKAGING & ACCESSORIES
Let’s start by how the TS-133 is presented. The retail box of the QNAP TS-133 NAS is definitely a change of scene from the plain brown box design of bigger releases by the brand and this is almost certainly down to the system being more readily available for buyers to see in retail outlets. The majority of NAS solutions are eShop purchases, but more affordable solutions such as the TS-133 are going to be considerably more high street accessible in your local tech shop. The packaging is a mix of European graphical shouting and eastern specification details. Maybe lacking a little of the subtlety of the TS-130 and TS-128A that came before it, it is still a nice looking box that I would stop to look at, to be honest.
Another area that the QNAP TS-133 NAS differs from bigger and more expensive releases is in how the unit is packaged. As this is a smaller and more compact unit, as well as more cost-sensitive, the protective packaging on this system is all cardboard (no hard foam framework) and it is packed pretty tight with the NAS, accessories and documents. Once you have unpacked it, good luck getting it all back in there!
The accessories of the QNAP TS-133 NAS are pretty standard stuff, with the kit including screws for 2.5″/3.5″ storage media, documentation on your warranty, warranty extension option, setup guide, 1 metre Cat 5e RJ45 LAN cable and the external PSU that the NAS arrives with. Once again, the box was pretty tiny and I am surprised how much they crammed in there.
Once everything is all laid out on the desk, you get a better idea of the scale of the QNAP TS-133 NAS. This kit does not include any HDD/SSDs, but the support of media is pretty wide and this NAS supports upto 20TB via a single Hard Drive in the available bay – though DO remember that hard drives greater than around 8TB (and Pro series drives of all capacities) will be noticeably noisier in operation and the TS-133 will not be able to hide this.
The external PSU of the QNAP TS-133 NAS is a 36W block style and fairly generic. Having an external PSU will ensure that the heat that it might generate is not inside the chassis (resulting in increased fan operation to compensate, potentially lower CPU efficiency and a noisier experience). Equally, thanks to the modest CPU inside this system, compact design and modest connections, this system is exceeding low in power consumption in both idle and active use – something that those looking for a NAS for their mobile home, boat, easy-deployment storage and mobile work desk space will appreciate.
Overall, the QNAP TS-133 NAS retail kit is all fairly standard stuff and although I wasn’t exactly bowled over by it, it contains everything you are going to need (aside from media) to set this device up in your home or office space. Let’s talk about the design of the TS-133.
QNAP TS-133 NAS Review – Design
The chassis that the QNAP TS-133 NAS features is a modified version of the TS-130 chassis that arrived back in 2020/2021. It is a surprisingly compact plastic casing, white in colour and features a mesh/quilt patterned black stick that details the system information at a glance via LEDs. The system does not have any side panel ventilation, instead opting for a larger system of smaller vents located around the entire chassis. I definitely prefer this colour scheme and slightly sharper edges of the TS-133 over the baby-blue TS-130 NAS Chassis.
Indeed, although some users are less keen on white chassis (as they can show dust and marks much more) this plastic chassis here is very low noise (will touch on this later) and will merge into more hardware environments very easily. It reminds me a lot of the 1-HDD WD My Cloud/My Book design and how it is designed to be understated and fit into your other desk/office hardware easily. This does as much quite well – though maybe it would have been nice for other colours to be available? A missed home user opportunity perhaps (it sounds crazy, but enough users have asked me this very question to wonder).
The top right of the front of the QNAP TS-133 NAS features individual LED indicators that denote different activities. These LEDs can be dimmed/deactivated in the QTS system and denote the following:
- System Activity
- Network Activity
- Storage Media Activity
Despite QNAP being one of the last brands to still feature LCD screens on some of their systems to give real-time information such as system temp, IPS, warning details etc, the budget level ranges such as this one have never and almost certainly will never have that kind of on-system digital UI.
Ventilation on the QNAP TS-133 NAS is an interesting subject (I mean, relatively interesting, I am not mad!). As this system is noticeably smaller than more other NAS drives AND it features a more power-efficient CPU, heat is going to be more of a concern than usual. Although the system is quite small, there is quite a lot of passive ventilated airflow working in conjunction with the active rear cooling fan. Although the bulk of the ventilation is based on the bottom of the device, the chassis is indented on either side, allowing the air to pass over the vertically stacked HDD bay inside and through the vents at the base as needed.
When the QNAP TS-133 NAS is in operation, the cooler air is pulled from the base, over the drive media and internal component heatsinks, then pulled through the rear cooling fan out the rear of the system. As the system does not feature any trays that would allow air to exit or ventilated side panels, it means that this airflow can’t escape any other way. The system uses a closed chassis and this ventilation is a big part of how the more efficient components maintain ideal operational temperature.
So, that is the design of the QNAP TS-133 NAS. It is certainly designed in a much more modest and understated than beefier NAS’, such as the TS-251D or TS-453D, but for compact deployment where you will want as little impact as possible in noise or physical space, it’s a solid bit of design. Let’s discuss the connectivity of the TS-133 NAS.
QNAP TS-133 NAS Review – Ports & Connections
As mentioned, the QNAP TS-133 NAS features a rear-mounted active cooling fan. This fan and the covering vent cover around 40% of the rear of the chassis and is surprisingly low noise. When you first boot the device up, it will spin at the maximum speed for a few seconds (as it tests that its functions are fully operational) and although the fan at the height of its speed is audible, it is still not the worse I have heard. In the 8 hours of hardware/software testing that I performed on this device (including software overviews, storage setups, Plex media server and more), I never heard the fan spin up particularly and the only particularly noticeable noise was the single Seagate Ironwolf hard drive I installed inside, which the TS-133 was unable to disguise/suppress.
For all of my positivity about the QNAP TS-133 NAS up to this point, it is worth highlighting that in terms of connectivity (and I am aware this is a much more modest, affordable and compact system), the external connectivity on the rear of this NAS is pretty underwhelming. QNAP in the last 18-24 months have revealed a number of innovative solutions to their Home, Prosumer and SMB (small-medium business) ranges that have largely led the way on connectivity – whilst still maintaining the same price point as fewer connectivity equipped systems from rival Synology. However, the TS-133 makes very little change in the connectivity compared with its 18-24 month older predecessor (the QNAP TS-130) and the 1GbE network port on the TS-133 is a particular blow. With Internet Service Providers rolling out 1Gb+ internet speeds in many countries AND providers such as Virgin in the UK releasing 2.5GbE equipped routers, we are fast reaching a point where one of the prime benefits of NAS vs Cloud (namely, the fact you can access a NAS faster than the cloud) is potentially being undone. Even if the TS-133 NAS is designed as an affordable solution, QNAP released several units in 2020/2021 that has 2.5GbE at the same price as 1GbE – so why does this system still have just 1GbE RJ45?
The System hardware inside the QNAP TS-133 NAS can certainly saturate 1GbE/100MB/s+ with/without encryption externally and alongside the benefits of even a modest non-pro HDD or SSD in this 1-bay allowing speeds of 24-360MB/s easily, QNAP also state that you CAN use the USB-to-5GbE adapter (optional purchase). So there does not seem to be any CPU limitations to using greater than gigabit connectivity and therefore its absence in even a modest device like this in 2022 is a tad disappointing.
Then, after the slight disappointment of 1x 1GbE, I then saw that the TS-133 arrives with 1x USB 2.0 port – IN 2022! Now, I am not unreasonable. I appreciate that 1) this is an affordable solution 2) that the processor and its hardware limits/chipset might be stretched and 3) that the system DOES also feature a USB 3.2 Gen 1 Port type-A too. However, given that this device can be used with USB backups, USB 3.2 Gen 1 network adapters, expansion chassis and more, having one of the USB expansion ports with considerably lower bandwidth version 2.0 ports is a real pain. They can still be used for things such as USB printers or UPS Heatbeat/alert connectivity, but as this system lacks any HDMI out (As the CPU does not feature any kind of embedded graphics), you cannot even use these for a KVM setup.
Overall, the connectivity on the QNAP TS-133 NAS is… well… fine. It’s fine and jsut about passable for an entry-level/affordable solution that is not exactly designed to knock your socks off. Nevertheless, it is not exactly going to blow you away in the bandwidth department. Next, let’s talk about the internal hardware.
QNAP TS-133 NAS Review – Internal Hardware
The internal hardware of the QNAP TS-133 NAS is understandably modest and although the system supports a good % of the QNAP QTS applications, it has to be said that its ability to multitask and/or support multiple users at once is noticeably less than an Intel/AMD x86 system would be. The single media bay of the TS-133 NAS allows a drive to be held in place (there is no tray and hot-swapping is not supported) internally via a SATA connection. To gain access, flip the device over and then unscrew the single base level flathead screw. It is that straight forward and after it is removed, the chassis can simply be slid apart into two pieces to reveal the media bay.
The drive bay is connected with a SATA combined power and data connector (no loose cables) and you can install either a 3.5″ or 2.5″ SATA HDD/SSD. The system is designed around an aluminium framework that is full of spacing for the airflow to work around and between the internal media, controller board and component covering heatsinks. The TS-233 2-Bay version of this system featured two trays that allowed the much easier screwless installation of media, whereas things are a little bare-bones in the TS-133 NAS. This is not the end of the world and only adds around 2-3 minutes to your installation though.
Now, some users do not consider a 1-Bay NAS system a suitable 24×7 server system for anyone, as the single HDD architecture means that you cannot take advantage of RAID (redundant array of independent disks) that allows you to have a safety net in the event that a HDD/SSD fails (nothing lasts forever). However, I would also be keen to highlight that RAID is NOT a BACKUP! If you are storing data that you deem irreplaceable (eg photos of family or events) or mission-critical (client/customer data for your business), then you NEED to have at least one (ideally x2) copy of your data at all times. So, although the loss of RAID in the TS-133 NAS is going to be a bit of a bummer for some, it DOES still arrive with support of Backups between the NAS and USB/Cloud/NAS, with the option to create many, many scheduled jobs in the HBS3 program. These can be conducted in either direction and although lack the short recovery of service that a RAID can provide, they are real BACKUPS and will be your saviour in the event of a critical system failure, ransomware attack, malware attack, theft and more.
The CPU of the QNAP TS-133 NAS is a Cortex A55 processor that is 64bit ARM in architecture, quad-core and has a clock-seed/frequency of 1.8Ghz per core. This CPU is one that is designed for long, long use whilst using a very small amount of power. ARM processors are often popular on mobile devices, tablets, Chromebooks and ultimately devices that are designed with efficiency in mind. However, this CPU (much like the A53 Realtek RTD1295 in it’s predecessor, the TS-130) is a server optimized processor and although would be outpaced by the likes of a Celeron, Pentium or Ryzen, it is ideal for keeping within the price point of most cost-effective buyers, whilst still providing a wide variety of supported software and services.
There are several versions of this CPU architecture in the market, but they all share a lot of functional similarities. ARM processors compress the instructions that are handled by the processor in order to use less power in their operation for the rest of the system. So, on the one hand, it means less power is used when typically operations are required HOWEVER it also means that it cannot handle particularly complex tasks, as they are either impossible to compress or the act of compressing these instructions takes way too long. The use of efficient CPUs like this in modern value NAS is not new (all the NAS brands do it), but this is the first time we have seen this particular CPU in a 2022 Value series NAS and almost certainly this will be a familiar architecture moving forward from the likes of Synology and Asustor soon.
Under the same CPU is an area of flash memory where the QNAP operating system lives (at least till it is initialized with storage media) and allows the system to be restored if needed, as well as set up from scratch without the use of the internet. This is fairly common in QNAP NAS systems and I can confirm that when the review unit arrived here in the studio, it featured the latest version of QTS 5 onboard.
The QNAP TS-133 NAS also features DDR4 memory that works in conjunction with the CPU to support your software and services when using the NAS (much like any other computer device). However, there is good news and bad news. The good news is that the TS-133 arrives with 2GB of DDR4 memory – which is noticeably more than most brands currently offer at this price point for a 1-bay (with the majority of others under £100 arriving with just 256MB or 512MB). However, the bad news is that you cannot upgrade this memory (as it is soldered to the controller board), so although 2GB is still more than other modest/Value NAS systems like this, you are going to hit a glass ceiling pretty quickly if you plan on using this system particularly aggressively. When I had a small handful of applications running on the TS-133 (media, surveillance and 1 backup task), I only had 0.7GB of memory left available according to the task manager. So, that 2GB memory DOES allow you to run several tasks, but if you are considering a larger body of software, users or scheduled tasks to be regularly performed, you might find this system will hit a wall sooner than you might like. Like most modest systems, the TS-133 is about staying realistic about how much you are paying for, the hardware that money gets you and what it can realistically be capable of. For the hardware on offer and my software experiences, I was pleased with what this system could do. I just wish there was the option of adding more memory later on. Let’s talk about software.
QNAP TS-133 NAS Review – Software & Services
I have rather laboured the point about the internal hardware of the TS-133, but this is mostly because many users will not understand the difference between power and capability, and this is very often an area where a buyer will fall into the tricky area of Budget Vs Cheap. I believe that this NAS falls into the category of value, not cheap – but let me explain. The QNAP TS-133 is more than just hardware and arrives with the QTS 5 NAS software. This service package and GUI is included in the price of the TS-133 (along with numerous mobile and client applications for multiple platforms) and is a relatively easy user interface to navigate (though not quite as user friendly as their more expensive rival Synology and DSM of course) and is an operating system that will support those users in both home and business circles. it is important to understand that when you buy the TS-133 server (or indeed any QNAP NAS) that it arrives with the QTS software platform included, BUT with constant updates and hundreds of applications included that NEED to be updated in their lifetime for reasons of security and increased services. If you want to use the QTS system, it is highly recommended that you always enable the myriad of security councillor, scanning and network security tools included. These are all tested and maintained 1st party QNAP apps and 3rd party applications. This is further improved with desktop client programs for PC/Mac and mobile applications for iOS and Android – ALL INCLUDED and downloadable at any time. The TS-133 can perform most modern applications that you would want from a modern NAS. I reviewed QNAP QTS 5 late last year over on YouTube (and here on the blog) and although these reviews were based on a more powerful QNAP NAS, the bulk of the services and features covered are supported by the TS-133 – just on a smaller scale:
| FULL Written QNAP QTS 5 Review | FULL Video Review of QNAP QTS 5 |
 |
Of course, with such modest hardware under the bonnet, how much of the QNAP software can this system hope to run? I can say that it definitely runs well/better than the TS-130, however as mentioned, the 2GB of DDR4 memory that the TS-133 arrives with (which cannot be upgraded) will likely use a significant chunk of that just to run a small handful of applications at once. The QNAP TS-133 is more than just hardware and arrives with the QTS 5 NAS software. Along with a bunch of others, the key tools, the TS-133 can perform most modern applications that you would want from a modern NAS, such as:
First Party QNAP Applications for the TS-133
- QSync for Backing up multiple Devices to the NAS on a schedule/as needed
- Hyper Backup Sync 3
- QuMagie for photo collections and AI-enabled face/thing recognition
- Multimedia Console for managing media sharing, streaming, transcoding and indexing
- File Station for File Management, sharing and permission allocation
- Download Station for managing HTTP/FTP/NZB/BT downloads, as well as RSS feeds for podcasts and updates
- QFiling and QSirch to better organize files and remove duplicates/waste
- Cloud Drive for Migrating and Synchronizing between Google Drive, Dropbox, Amazon S3, etc
- Photo Station to organize and catalogue photo collections
- Music Station to organize, playback and stream music media to network/internet devices
- Video Station to playback media over the network/internet
- Container Station for management micro/compact virtual environments
- QVR Elite for Surveillance/CCTV/NVR use with IP Cameras
- MANY more QNAP Apps
Third-Party Applications for the TS-133
- Plex Media Server(no transcoding natively)
- Emby
- iTunes Server
- Acronis True Image Backup
- Malware Remover
- SugarCRM
- TVMosaic
Overall, I cannot especially fault the range of applications that the QNAP TS-133 NAS arrive with, as at this price point for all these to be included with the hardware (more than just applications, but it has evolved into an entire operating system with services, client tools and wide-ranging usage options). It is still a device that requires a higher than average understanding of technology and its position of trying to hold your hand in the menus, whilst simultaneously throwing setup options at you (with each saying that are important and you need to stay secure) means that it can be a pinch intimidating. You should not by a device like this and think that the end of your data storage, security and backups ends at the point of plugging it in – that way leads to the loss of data and lots of lost nights of sleep, but still, for this price point it is really hard to fault the value here for the combination of hardware and software.
QNAP TS-133 NAS Review – Conclusion & Verdict
As long as you keep your feet on the ground a little and stay realistic, the QNAP TS-133 NAS Drive is indeed a very impressive piece of kit. We are talking about a combined hardware and software solution that you can purchase with a 4TB drive from the likes of Seagate or WD inside all in for a little over $200. It can run plex media server, it has surveillance software included in QVR Elite, AI-powered photo recognition (with the system featuring a dedicated AI engine for these tasks), multi-tiered backup handing in Hybrid Backup Sync 3, host a DLNA media server, connect and synchronize with cloud services in a bunch of ways, access to a bunch of tailored mobile apps and a whole lot of other services that would take too long to mention. Also, the TS-133 NAS is the first system in the commercial NAS market to feature this new Cortex A55 processor, as well as twice (and in some cases) four times the memory of alternative systems in the same tier with it’s 2GB DDR4 RAM. As long as you have realistic expectations about how busy you are going to be, how hard you intend to push the device and how much you expect it to do at any one time, I think the QNAP TS-133 NAS is easily the most powerful and capable 1-Bay NAS in the market to buy right now. The non-upgradable memory is a pain, the lack of 2.5GbE is perplexing and the continued appearance of USB 2.0 is a tad infuriating, but the TS-133 seemingly makes up for it with a wide variety of applications supported, a remarkably subtle and discreet deployment and in the hands of the right low-level user, this might well be the best NAS QNAP have produced in the value tier for years!
| PROs of the QNAP TS-133 NAS | CONs of the QNAP TS-133 NAS |
| Currently the most powerful 1-Bay NAS Drive in the market
A 1-Bay with 2GB of DDR4 Memory is pretty rare in the Value tier Exceptionally low noise and power use Runs the latest version of QTS 5 First Value Tier NAS in the market to use the Cortex A55 Processor Quad-Core Processor is a nice bonus Inclusive AI-powered component built into the hardware Support for NAS-to-NAS/USB/Cloud backups and also supported Hybrid Storage and mounting |
1GbE in 2022 event at the value tier is underwhelming
USB 2.0 Ports is equally underwhelming Lack of RAID will put some users off (applicable to all 1-Bay’s though)
|
🔒 Join Inner Circle
Get an alert every time something gets added to this specific article!
This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below
Need Advice on Data Storage from an Expert?
Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you.
 |
 |
(Early Access) The BEST Photographer and Video Editor NAS (2024)
(Early Access) COOL NAS UPGRADES (You might Not Know About)
(Early Access) UGREEN NAS SERIES - SHOULD YOU BUY?
(Early Access) DIY NAS - The Cost of Building a Synology NAS?
(Early Access) The Best DIY NAS Builds for Under $500
(Early Access) DIY NAS vs Lockerstor Gen 3 - IS IT WORTH $1299 ???
(Early Access) Lockerstor Gen 3 Series - SHOULD YOU BUY ONE?
(Early Access) Asustor ADM 5 Software Review - Should Synology Be Worried?
(Early Access) Best 8-Bay NAS of 2024
(Early Access) Best 4-Bay NAS of 2024
(Early Access) Best 2-Bay NAS of 2024
(Early Access) Best Value NAS of 2024 - SAVE SOME MONEY!
Access content via Patreon or KO-FI
