How to Upgrade the RAM in your Synology DS918+ to 16GB Memory
Back in 2017 when the Synology DS918+ was first released, many users were surprised at the maximum memory limit that the manufacturers stated ion the specifications. With the Intel J series chip that Synology DS918+ arrives with, it did seem odd that the maximum or 6GB or 8GB of DDR3L memory (both Synology and QNAP have their own stance on this) for this chip was listed firmly in the specification. On the face of it, 6GB of 8GB seems like plenty. That will comfortably support the NAS tasks of a plex media server, all those productive first party NAS applications and backups. However, as file sizes grow, as NAS surveillance gets popular, as virtual machine and container station applications grow in popularity, it will not be too long before you will see that memory use ALWAYS above 80% in the task manager. Sadly, we have asked the manufacturers and they continue to stand by the fact that you cannot exceed this limit, officially.
However, I am pleased to tell you that I have been experimenting with several different sizes of RAM sticks and various brands, and am pleased to confirm that not only can you use non-official own-brand memory in the Synology DS918+, but also that you can install two 8GB sticks of DD3L RAM (one per slot) meaning you can have a Synology DS918+ with 16GB of Memory! Read below for my guide, it will detail how to install the RAM, how to check that it is installed correctly and how to test that it is working straight away.
Upgrading your Synology DS918+ to 16GB of Memory – Pay Attention
Before we continue with the guide, it is worth highlighting that the Synology DS918+ manufacturer strongly recommends that you do not exceed the stated memory limit on their specifications page. They also highlight that using non-official memory in your Synology DS918+ may invalidate your warranty. We at NASCompares cannot be held accountable for how you use this guide. However below I will show you where to buy the individual memory and Synology DS918+ NAS device you will need. Only attempt this upgrade if you are comfortable with the terms laid out above by the manufacturer. Alternatively, you can buy the Synology DS918+ with 16GB pre-installed using the link below and this unit will arrive TESTED and with SPAN, the NAS experts, ensuring your warranty is unchanged.
Where to Buy the Synology DS918+ with 16GB Memory
16GB Synology DS918+ Memory Upgrade – Step 1, Physical Installation
What you will need:
- A Synology DS918+ NAS – Obviously
- 2x Crucial 8GB (16GB Total) Memory Upgrade – Link below
- Small Phillips Head Screwdriver – (kinda optional but recommended for chassis)
- (OPTIONAL) Anti-static gloves and Envelope – useful to eliminate static charges and also to store the removed older official memory sticks):
First, we need to ensure the Synology DS918+ is completely powered down/off and the mains power has been disconnected. It is recommended that you remove the Hard Drive or SSD that you have installed before accessing the RAM as it may block the slots. Additionally, you should remove the hard drive media as the unit will be moved around a lot during the memory installation and this could damage the drives. Be sure to keep a note of the drives that you remove and the order they were installed (HDD Bay 1, HDD Bay 2, etc) as installing the drives in the wrong slots could damage any existing RAID you have setup internally.
|NAS HDD #1||NAS HDD #2||NAS HDD #3||NAS HDD #4|
Next, we need to access and remove the existing memory, as the news 16GB of memory for our Synology DS918+ will occupy both slots. Be sure you eject the official memory sticks using the clips either side of the slot, as well as only holding the memory sticks by the narrow side edges, never touching the chips or board of the money or NAS.
Once you have removed them, they can either be stored away for a later project, installed in a compatible laptop or sold on eBay etc to make a little cash back! Once they are clear, install an 8GB Crucial Memory stick in each of the now available slots, making sure that you click them both in with the clips either side. Once down, replace the Synology DS918+ chassis lid if you removed it for ease of access, as well as the hard drives.
You have now concluded the physical installation of 16GB of crucial memory in the Synology DS918+.
16GB Synology DS918+ Memory Upgrade – Step 2, Checking the 16GB Memory is Recognized
What you will need:
- A web browser (Chrome, Safari, Firefox, etc) on a Windows, Mac or Android Machine) accessing the Synology DS918+ user-interface as you normally would.
Next you need to power up your Synology DS918+ NAS and access it as you normally would. If you are buying this NAS first time and have yet to set it up, there are numerous first time set up guides and tips on the SPANTV YouTube channel here – that will get you from the hardware installation to set up the Synology DS918+ NAS for use. Once the NAS user interface (UI) is ready to go, head over to the hardware specification page shown here:
As you can see from this CPU and Memory display, the Synology DS918+ has recognized and made available the 16GB of crucial memory. It will be immediately available for use and you will see that the % amount of use of the RAM in the resource monitor will be much, much lower, as there is significantly more memory available for the system!
16GB Synology DS918+ Memory Upgrade – Step 3, Checking the 16GB Memory is Working
There are several ways to check the memory is working on your Synology DS918+ correctly. First, you can perform as many actions and processes as possible (scans, copy/pastes, thumbnail generation, transcode a 4K file, RAID changes, synchronisation, etc) at once to see how the task manager and resource monitor behaves in the Synology DS918+. It should spike each time and at a greater height as you do more and more and once it exceeds the memory you had previously installed, this is a good confirmation that the installation is working fine.
Alternatively, you can temporarily allocate chunks of memory and then that is a much more reliable test. Install the virtual machine application for the Synology DS918+ (P.S. for Synology users it is the Virtual Machine Manager and for QNAP it is the Virtualisation station). Then you can create individual VMs (it is alot easier than it sounds and the Synology DS918+ VM software is very user-friendly) then allocate 3-4GB of memory to each one. When you have created 3 or 4 individual virtual machine containers on the Synology DS918+ software, then you can run them all at once and that will immediately use almost all the memory at once! If there are any issues with the memory, it will show here almost immediately. If no problems, then you know the Synology DS918+ 16GB crucial memory installation as successful. You can then delete the VMs in the virtual machine software and then free up all that memory again.
📧 LET ME KNOW ABOUT NEW POSTS 🔔
Get an alert every time something gets added to this specific article!
This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below
Need Advice on Data Storage from an Expert?We want to keep the free advice on NASCompares FREE for as long as we can. Since this service started back in Jan '18, We have helped hundreds of users every month solve their storage woes, but we can only continue to do this with your support. So please do choose to buy at Amazon US and Amazon UK on the articles when buying to provide advert revenue support or to donate/support the site below. Finally, for free advice about your setup, just leave a message in the comments below here at NASCompares.com and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry.
Support What We Do
Terms and Conditions Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own. This description contains links to Amazon. These links will take you to some of the products mentioned in today’s video. As an Amazon Associate, I earn from qualifying purchases
DISCUSS with others your opinion about this subject.
ASK questions to NAS community
SHARE more details what you have found on this subject
CONTRIBUTE with your own article or review. Click HERE
IMPROVE this niche ecosystem, let us know what to change/fix on this site
EARN KO-FI Share your knowledge with others and get paid for it! Click HERE
5 thoughts on “The DS918+ NAS Supports upto 16GB Memory – An installation Guide”
Thanks so much for your guide. I have been using but otherwise neglecting my 918+ for some time. Recently, I decided to move a bunch of apps to Docker. I then went down the rabbit hole of looking to upgrade the memory and adding SSD cache. I used your blog posts to do both and now my 918+ is up and humming!
Thanks for this post.
My DS918+ didn’t start after upgrade memory. Only blink the power button for long time. Do you know why?
Sometimes you need to leave the NAS for an hour for it to run all tests. But if that doesn’t help, this RAM might be faulty or not compatible.
User email : “My DS918+ with 12 GB unsupported RAM is now running on the updated to DSM 7.1-42661 Update 3
I can confirm the exact make and spec of the RAM Royemai / DUOMEIQI Non-ECC PC3-12800 DDR3 1600Mhz 8GB 2Rx8 1.35V CL11 Non-ECC Notebook RAM
So I have the Synology default 4Gb + this 8Gb so a complete mismatch but it has worked flawlessly for years.
What memory types did you use for 16GB RAM with DS918+? Cant find any information or link on your blog 🙁