Synology SRM 1.3 Update for MR2200ac and RT2600ac Routers FINALLY!!!

Synology Release SRM 1.3 for the RT2600AC & MR2200ac Router for Adding RT6600ax Mesh Setups

Good news for those of you who have been considering upgrading their existing Synology router mesh setup OR those who already own the previous releases in the Synology Router series with the announcement of SRM 1.3 for the RT2600ac and MR2200ac devices. Synology Router Manager (SRM) 1.3 was released with the newest device in the brand’s router lineup, the RT6600ax, but not made available for the previous generation devices immediately. The newest version of SRM includes multiple improvements to the GUI, included applications and services, added vLAN support and (most important of all) now means that those of you who have an existing MR2200ac Mesh network in place can now connect with the RT6600ax (that many opted to replace the RT22600ac in their existing set ups). Updating your Synology MR2200ac and RT2600ac to SRM 1.3 SHOULD be very easy as soon as the Release Candidate of SRM 1.3 is available on the official download pages (HERE for the MR2200ac and HERE for the RT2600ac) as you will be able to manually download and update your system OR head into the control panel and allow the router to check the Synology update database and update directly.

Important Note About Using MR2200ac as a Mesh Node for the Synology RT6600ax Mesh Router

IMPORTANT!!! If you are running an RT6600ax WiFi 6 Router and want to add a batch of new/factory restored MR2200ac Mesh Points, you will need to go through the process of updating each node from SRM 1.2 to SRM 1.3. However, unlike Synology NAS systems during initialization, there is no point in the first-time setup of the MR2200ac/RT2600ac to upload a firmware file or the system search for the latest firmware online. This is only possible AFTER the router is initialized and from there, you will need to download the latest firmware (SRM 1.3), allow the system to reboot, THEN reinitialise the MR2200ac/RT2600ac so it can enter a ‘find’ status (when the LED on the system is a single, flashing blue light). From THAT point, you can find the MR2200ac/RT2600ac in the WiFi Access Point Search of your RT6600ax Router and add these nodes successfully. So:

  • ALL Synology MR2200ac Mesh Routers will need to be updated individually to SRM 1.3 before attempting to connect with an RT6600ax Router Network
  • SRM 1.3 Update can be downloaded from the Synology site OR from the MR2200ac initialization (coming soon, after Release Candidate and final release are made public online)
  • First-time initialization and setup in 1.3 has been updated, so the initialization of a Router with SRM 1.3 on board is much simpler and more user-friendly
  • If you try to connect your RT6600ax to an MR2200ac mesh node without updating that mesh node to SRM 1.3, it will SEE the MR200ac, but it will not be able to connect it due to firmware incompatibility between SRM 1.2 and SRM 1.3

It is worth highlighting that from then onwards, your primary router will be able to push updates to the nodes individually (much as the RT2600ac pushes updates to the MR2200ac mesh router points). No doubt as time goes on, this method of updating with be considerably easier and as newer routers go through manufacture, they will have SRM 1.3 onboard by default.

IMPORTANT #2! – If you are migrating from an RT2600ac to an RT6600ax Router, make sure to update the RT2600ac to SRM 1.3 first, then backup your router configuration in the control panel by heading to Control Panel > System > Update & Restore > Backup Configuration. From here you can create a config file that you can store locally on your computer, which can then be used to reinstate your configuration on the new RT6600ax. SRM 1.2 configurations cannot be used on an SRM 1.3 Router

Installation of SRM 1.3 on the Synology MR2200ac Router

First of all, upgrading to SRM 1.3 is much the same as typical firmware updates in Synology products IF you already have the device setup and can log in to the GUI.

Updating an MR2200ac or RT2600ac via the GUI

Log into your Synology MR2200ac or RT2600ac and head into the control panel, then select System, then Update & Restore, then select Manual SRM Update.

From here browse your local machine and find the .PAT file that you downloaded from in the download area of the RT2600ac or MR2200ac, then select it and choose to install this update

You will be greeted by a pop-up that states that this update may change or remove some features of SRM 1.2 in line with SRM 1.3. Additionally, it will stop backup configurations you have made of SRM 1.2 from working in this new revision of the software. From here you can click confirm to proceed

The system will start uploading the SRM 1.3 pat update file to the MR2200ac or RT2600ac router

You will then be informed that in order for the update to take effect, then you will need to restart

During this installation and completion of the SRM 1.3 update, the router and its services will not be accessible.

When the installation of the first part of the SRM 1.3 update is completed, the system will reboot and a clock will count down. If the router GUI does not reappear in the browser after this time, it may well be because the router was on a dynamic IP setting and has changed it’s address. Use the Synology Assistant tool to find your Synology MR2200ac or RT2600ac’s new address.

When the system reboots, it will book back into the login GUI, but now it will be the improved and further polished SRM 1.3 login screen. From here you can log in as normal and enjoy SRM 1.3 with new features.

Next, lets discuss what you need to do in order to add existing MR2200ac and RT2600ac routers to a mesh network with the RT6600ax Router.

Adding a Synology MR2200ac or RT2600ac Router to the Synology RT6600ax Router as a Mesh Point

In order to add a Synology MR2200ac or RT2600ac to your RT6600ax Router as a mesh point, you will need to ensure that they are running SRM 1.3 as their firmware. In the case of the RT2600ac, this will be REALLY easy, as you can access the main SRM 1.2 GUI and update to SRM 1.3 as the software appears on the Synology Download section. However, in the case of MR2200ac nodes (which are rarely used as a primary router) you are going to need to update each node with SRM 1.3 before they are seen by the RT6600ax. If you have them connected with an RT2600ac, it is easy to push the update to SRM 1.3 across the whole existing network. However, if you only have the RT6600ax and 1 or more MR2200ac mesh routers, each one will need to be updated to SRM 1.3 using the steps in the guide above THEN formatted to factory settings.

If your MR2200ac is on SRM 1.2, follow the guide above to upgrade it to SRM 1.3. If you have updated your MR2200ac to SRM 1.3, you now need to restore it to factory settings here:

Doing so will result in the device deleting all data and settings – so be sure that this is what you want to do. Proceeding with this will result in the device taking 5-10 minutes to complete.

Alternatively – you can reset your MR2200ac router by using the reset pin on the rear of the router. However, this will not allow you to make any configuration backups and is irreversible.

Next, head over to your Synology RT6600ax Router and head into the WiFi Access Tab to start adding WiFi points/Nodes

You will be asked which connection method your nodes will be connected by. I STRONGLY recommend selecting both ethernet and wireless connections

The reason I recommend this is that it is about 100x easier to set up a smaller mess network of around 5-6 nodes by bringing them all together and connecting via LAN to the RT6600ax, then later disconnecting them and positioning them where you need them to be. It IS worth remembering that later on when you get them up that their distance from the primary router will affect the strength BUT (crucially) when a Synology mesh router is connected with the RT6600ax primary router, it knows the wifi identity and security credentials of the node and will connect wirelessly with the MR2200ac etc as soon as it is within range (even if the primary connection was via wired ethernet).

Note, if you are connecting the nodes (temporarily for setup or long term) via ethernet, you need to ensure that the MR2200ac or RT2600ac has cable connected to the WAN port and into a LAN port of the RT6600ax. Otherwise, the connection/host-client communication will not function correctly. Again, later on, after the node is set up, you can move these nodes away and the wireless connectivity will also function between the mesh points.

After this, there are a few steps to highlight the best places to set up a mesh node (in terms of proximity and multiple points), but also a note that you need the mesh mode in the correct LED lit configuration (that single blue flashing light)

When the RT6600ax scans the local network for the other Synology router to extend the mesh network, it will list the router(s) it has found and then invite you to enter the secure pin code that is printed on the back of all Synology routers (8 digits, numerical, cannot be changed)

After that, the RT6600ax Router will begin setting up the new mesh WiFi point (testing the strength of connection, copying over the SSID configuration and establishing the backhaul). This will not take more than a minute or so per node and (unless the mesh node has been obstructed, powered down, or has not been updated to SRM 1.3) should connect to the RT6600ax network.

And that is it. Now the MR2200ac or RT2600ac are part of your RT6600ax Mesh router system. They will no longer appear on the Synology Assistant tool and their SRM GUI cannot be accessed – they are now connection nodes to the larger RT6600ax router system and can be managed and adjusted in the SRM 1.3 GUI of the primary router. You can also power down the mesh router nodes and move them to new locations in your home or office for greater coverage. When they power back on, as long as they are in the coverage area of the primary router, they will re-join the RT6600ax/Primary router network automatically. If they are in a weak area of coverage/distance, the system will let you know and recommend which ones need to be brought closer.

If you are still unsure about the benefits of SRM 1.3 and debating whether purchase a Synology Router (or maybe you have one and you are unsure whether to upgrade from SRM 1.2 > 1.3), you can use the video and article below where I fully reviewed SRM 1.3 on the RT6600ax Router.

Synology SRM 1.3 Video Review

Synology SRM 1.3 Video Review



Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 1,281 other subscribers

Get an alert every time something gets added to this specific article!

Want to follow specific category?

This description contains links to Amazon. These links will take you to some of the products mentioned in today's content. As an Amazon Associate, I earn from qualifying purchases. Visit the NASCompares Deal Finder to find the best place to buy this device in your region, based on Service, Support and Reputation - Just Search for your NAS Drive in the Box Below

Need Advice on Data Storage from an Expert?

We want to keep the free advice on NASCompares FREE for as long as we can. Since this service started back in Jan '18, We have helped hundreds of users every month solve their storage woes, but we can only continue to do this with your support. So please do choose to buy at Amazon US and Amazon UK on the articles when buying to provide advert revenue support or to donate/support the site below. Finally, for free advice about your setup, just leave a message in the comments below here at and we will get back to you. Need Help? Where possible (and where appropriate) please provide as much information about your requirements, as then I can arrange the best answer and solution to your needs. Do not worry about your e-mail address being required, it will NOT be used in a mailing list and will NOT be used in any way other than to respond to your enquiry.

    By clicking SEND you accept this Privacy Policy

    Terms and Conditions Alternatively, why not ask me on the ASK NASCompares forum, by clicking the button below. This is a community hub that serves as a place that I can answer your question, chew the fat, share new release information and even get corrections posted. I will always get around to answering ALL queries, but as a one-man operation, I cannot promise speed! So by sharing your query in the ASK NASCompares section below, you can get a better range of solutions and suggestions, alongside my own.  

    DISCUSS with others your opinion about this subject.
    ASK questions to NAS community
    SHARE more details what you have found on this subject
    CONTRIBUTE with your own article or review. Cick HERE
    IMPROVE this niche ecosystem, let us know what to change/fix on this site


    32 thoughts on “Synology SRM 1.3 Update for MR2200ac and RT2600ac Routers FINALLY!!!

    1. I’ve just ordered the RT6600ax (still using the RT1900ac) and I already have a laptop on wifi-6
      and a desktop on wifi-6E. I hope my transfer speed from my DS220J & DS218+ are better then
      the 25mb-50mb I’m getting at the moment over SMB I’m hoping 80+mb minimum on LAN
      and a 180+mb for WiFI.

    2. Easy firmware upgrade

      Message Body:
      I have 1 RT2600AC and 2 MR2200AC. I was able to upgrade all of them to 1.3 from RT2600AC with manual method. Once SRM is upgraded, export configuration from RT2600AC, and restore to RT6600AX. Everything works fine afterward.

    3. Did you have to reset to factory settings when upgrading the RT2600ac or MR2200ac while they are running in Mesh. I have 1 RT2600ac and 4 MR2200ac running in Mesh. I actually have 3 sites that I manage where 2 of the sites only have the RT2600ac. I am running the latest 1.2.5 on all of them. I know of other friends and family with Mesh setup similar. If I lost my srm 1.2.5 config settings it will be a problem. ALSO, I use Site to Site between the RT2600ac’s (any know issue with that?). Thanks.

    4. My Internet subscription entails daily 6gb quotas renewed every midnight within the subscription period. That said, I often exceed that limit and have to tether my phone to the 2600ac usb port. Due to the risk of losing the ability to temporarily restore internet access to my network through router-phone tethering, I will definitely not update SRM…probably never lol????.

    5. I assume that the MR2200ac does not support Wifi 6 in combination with. the RT6600ax and that we have to wait for an ax version?

    6. Alright M8. Great video as always. Still, how about you go ahead and try to force the install of SRM 1.3 on the old RT1900ac. You know, for s#!t’s and giggles. Could be an interesting follow up video. Too bad about the old RT1900ac though. Real shame that.

    7. Does the dns package support local network dns entries? I currently use ddwrt and have local dns records configured for a few server IPs…that way my desktop and mobile clients can connect to files and emails using those fqdn names locally

    8. Amazing review. Thanks a lot for your effort. It’s almost like we’re dealing with a Nas Station here. In terms of user experience anyway. I think if they added Plex, a lot of basic users wouldn’t have bought a Nas Station anymore, so I think is is a selling strategy here. Anyway, great review, I am considering buying an unit after watching your video. Well done mate! Keep up the good work!

    9. Looks fantastic. As mentioned previously, I am using a net gear R9000 which to be fair has been working brilliantly. I flashed it with DDWRT recently using my iPad Pro, it took an absolute age to login but finally it worked. I am registered as a blind person but enjoy fiddling around with technology. I am waiting for your video next week for The router shootout vid but, am quite taken with the RTÉ 6600.
      Thank you for all of your videos they are very helpful

    10. When the videos get this long ( which I do very much appreciate ), I head straight to the conclusion. If you conclusion is positive, I generally go back to the beginning. That’s what I’m doing here. Your opinion at the end is exactly what some of us need. I currently have an RT2600ac but now I will buy a new 6600 model and use the 2600 as an access point in the upstairs of my home. Many thanks for all of the time that you put into these reviews.